• Harmonic balancer

    From Jim Wilkins@21:1/5 to All on Thu Jun 30 18:22:08 2022
    I didn't know they could fail until mine fell apart while removing the alternator, which I thought was defective. Is that a common problem?

    The rubber separated from the hub but was still a tight fit.

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From Bob La Londe@21:1/5 to Jim Wilkins on Thu Jun 30 16:42:34 2022
    On 6/30/2022 3:22 PM, Jim Wilkins wrote:
    I didn't know they could fail until mine fell apart while removing the alternator, which I thought was defective. Is that a common problem?

    The rubber separated from the hub but was still a tight fit.


    I've heard they come apart at high RPM. I imagine they could come apart
    with age as well.

    --
    This email has been checked for viruses by AVG.
    https://www.avg.com

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From Clare Snyder@21:1/5 to All on Thu Jun 30 23:02:57 2022
    On Thu, 30 Jun 2022 16:42:34 -0700, Bob La Londe <none@none.com99>
    wrote:

    On 6/30/2022 3:22 PM, Jim Wilkins wrote:
    I didn't know they could fail until mine fell apart while removing the
    alternator, which I thought was defective. Is that a common problem?

    The rubber separated from the hub but was still a tight fit.


    I've heard they come apart at high RPM. I imagine they could come apart
    with age as well.
    Not terribly uncommon. I missed what kinf of car/engine and
    age/mileage

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From Snag@21:1/5 to Clare Snyder on Fri Jul 1 06:22:01 2022
    On 6/30/2022 10:02 PM, Clare Snyder wrote:
    On Thu, 30 Jun 2022 16:42:34 -0700, Bob La Londe <none@none.com99>
    wrote:

    On 6/30/2022 3:22 PM, Jim Wilkins wrote:
    I didn't know they could fail until mine fell apart while removing the
    alternator, which I thought was defective. Is that a common problem?

    The rubber separated from the hub but was still a tight fit.


    I've heard they come apart at high RPM. I imagine they could come apart
    with age as well.
    Not terribly uncommon. I missed what kinf of car/engine and
    age/mileage


    I had the outer ring on one creep back towards the engine until it
    was scraping on the timing cover on a small block Chevy once . Took me a
    while to figure out where it was coming from !
    --
    Snag
    “Free speech is my right to say what you don’t
    want to hear.” -George Orwell

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From Jim Wilkins@21:1/5 to All on Fri Jul 1 07:44:47 2022
    "Clare Snyder" wrote in message news:rsosbhd7g6n6cnn1i7n9opqdf86o3ndrul@4ax.com...

    On Thu, 30 Jun 2022 16:42:34 -0700, Bob La Londe <none@none.com99>
    wrote:

    On 6/30/2022 3:22 PM, Jim Wilkins wrote:
    I didn't know they could fail until mine fell apart while removing the
    alternator, which I thought was defective. Is that a common problem?

    The rubber separated from the hub but was still a tight fit.


    I've heard they come apart at high RPM. I imagine they could come apart
    with age as well.
    Not terribly uncommon. I missed what kinf of car/engine and
    age/mileage

    ---------------------

    2000 Honda CRV, 80,000 miles. For several years it's squealed briefly after starting in very cold weather if the battery had drained from a week or more
    of non-use. I thought that was the alternator bearing or belt slipping,
    because its pivot bolt had seized from road salt corrosion and I couldn't tighten the belt. Charging the battery the day before prevented the squeal. Perhaps the squeal was the outer ring of the pulley slipping. It drives the
    A/C and alternator, while the center hub drives power steering. I had
    noticed that the A/C belt seemed slightly misaligned. The belt area is
    cramped against the wheel well and hard to even see into unless the P/S is removed.

    I can't complain, for 20 years hardly anything went wrong with the car, just rust. But now it's 22 and showing its age. The 2002 and later ones had more problems. The dealer's lot is nearly empty and they told me the new car shortage may last two more years, until US semiconductor manufacture ramps
    up. Personally I could do without all the fancy electronics. I learned to control a skid on ice before ABS, for both cars and dirt bikes.

    I unbolted the mounting bracket to remove the alternator, then lagged it to
    a wood beam to beat on it without risking the engine block. What finally loosened the pivot bolt was a long steel bar milled to fit and twist the
    large square end. Twisting the threaded end only broke it off. The bearings hadn't seized but they did allow the rotor to rub and score the stator. I
    may rebuild it for practice and drive it with a small gas engine as a high current battery charger, like Neon John's, with a large rheostat as a manual regulator.

    Why are tracked vehicles rattling past my house?

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From Jim Wilkins@21:1/5 to Clare Snyder on Fri Jul 1 08:21:40 2022
    "Snag" wrote in message news:t9mlcm$28c16$1@dont-email.me...

    On 6/30/2022 10:02 PM, Clare Snyder wrote:
    On Thu, 30 Jun 2022 16:42:34 -0700, Bob La Londe <none@none.com99>
    wrote:

    On 6/30/2022 3:22 PM, Jim Wilkins wrote:
    I didn't know they could fail until mine fell apart while removing the
    alternator, which I thought was defective. Is that a common problem?

    The rubber separated from the hub but was still a tight fit.


    I've heard they come apart at high RPM. I imagine they could come apart
    with age as well.
    Not terribly uncommon. I missed what kinf of car/engine and
    age/mileage


    I had the outer ring on one creep back towards the engine until it
    was scraping on the timing cover on a small block Chevy once . Took me a
    while to figure out where it was coming from !

    -------------------

    Apparently they have no core charge value. I could use the parts as
    hydraulic press fixtures, or adapt the hub to a gas engine to drive the alternator with the original ribbed belt.

    The tracked vehicle was a paving machine, not military. One never knows,
    people collect militaria and I drove off the narrow road into the woods once
    to avoid an oncoming M113 APC. I've been the culprit too, helping
    re-enactors roll a cannon down a back road.

    Someone around here has a 105mm recoilless rifle on a Jeep. He had to make a fake breech from wood and styrofoam to keep it legal.

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)